Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
- 12. A body, salon
   12.2. The central section of a guard
   12.3. A cowl rope
   12.4. A forward guard
   12.5. A forward wing
   12.6. Lock pins of a cowl, the rubber shock-absorber
   12.7. A cowl
   12.8. A gazonapolnennaja rack (models the Sedan)
   12.9. A luggage carrier cover
   12.10. A back door (Compartment model)
   12.11. A forward door, the bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing stoppers, a window regulator
   12.14. The door lock
   12.15. Draught of lever transfer of the lock
   12.16. A rope of an internal door-lock
   12.17. A rotary clamp, an adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. The central lock
   12.21. The pump with two modes of forcing
   12.22. The leading activator
   12.23. The activator of a back door
   12.24. The activator of a cover of a luggage carrier
   12.25. The activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt overlay (Compartment model)
   12.28. A skeleton of a back door, the bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. A rope, шарнирный the lever
   12.31. The door handle
   12.32. The holder of components of a door
   12.33. The hatch
   12.34. A bumper casing
   12.35. Hermetic sealing of a back bumper
   12.36. An extending clamp
   12.37. A forward spoiler / a lining of a niche of a wheel (Compartment model)
   12.38. The top overlay of a forward spoiler (Compartment model)
   12.39. A back spoiler / a lining of a niche of a wheel
   12.40. A back bumper (Compartment model)
   12.41. window raiser
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. A central air
+ 14. An electric equipment




12.29. A bearing element of the back door, a condensing stopper
THE GENERAL DATA

Two washers with чашеобразной dredging can be in case of need established.

Adjustment of a bearing element of components of a door

The window and door skeleton too should be adjusted.

PERFORMANCE ORDER
1) ослабьте bolts
2) close a door
3) press on bearing element of components of a door in a direction opposite to a roof and a rack
4) the assistant should tighten at first bottom, and then the top bolts
5) 20 Н.м.
6) be convinced that the bearing element is established, having pressed on top more strongly
7) do not press a door skeleton
8) check up all the sizes long

The holder of components of a door, the sizes

In drawing the cross-section section of the left door is shown

With = 3.5 + 1 mm
d = 8.1 + 1 mm
1 – a sealing flange
2 – a door frame
3 – a decorative overlay of a door
4 – a window
5 – a window sealing lining
6 – an internal door sealing lining
7 – a sealant
8 – a sealant at a window

The sealing edge 7 should have contact on all contour of a rack and a decorative overlay of a roof 3

The external sealing flange of a window 8 should not support a decorative overlay of a roof 3