Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. A steering
   11.2. A shaft and a casing of a steering column
   11.3. A power absorbing steering column
   11.4. A steering drive
   11.5. The pipeline of high pressure / the return pipeline
   11.6. Free wheeling adjustment рейки a steering
   11.7. A klinovoj belt
   - 11.8. System of hydrostrengthening of a steering
      11.8.1. Technical characteristics
      11.8.2. Prorolling / filling of a hydraulic liquid
      11.8.3. Check on tightness (at the working engine)
      11.8.4. Steering transfer
      11.8.5. The pump of the hydraulic booster of a steering (Vickers)
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment




11.8. System of hydrostrengthening of a steering
THE GENERAL DATA

The pump of the hydraulic booster of a steering for 4-cylinder models

1. 20 Н.м.
2. An arm
3. 20 Н.м., always replace
4. An arm
5. 20 Н, m.
6. An arm
7. 20 Н.м.
8. A klinovoj belt, the size: 9.5 х850 mm
9. A bolt and a fixing nut
10. 20 Н.м.
11. A pulley, establish a mark "5Z" forward
12. 25 Н.м.
13. 20 Н.м.
14. The lopastnyj pump
Before installation fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel
15. A bolt "банджо", the inhaling moment: 50 Km
16. A sealing ring
Always replace
17. A soaking up hose
18.
19. A bolt "банджо", the inhaling moment: 50 Н.м.
20. A high pressure hose
21. An arm
22. 20 Н.м.

The pump of the hydraulic booster of a steering for 5-cylinder models

1. A bolt "банджо"
The inhaling moment: 50 Н.м.
2. A sealing ring
Always replace
3. 20 Н.м.
4. An arm
5. An arm
6. A klinovoj belt
The size: 12.5x992мм
7. 20 Н.м.
8. A pulley
Establish a mark "5Z" forward
9. 20 Н.м.
10. The tension device
11. 20 Н.м.
12. Самоконтрящаяся a nut
The inhaling moment: 20 Н.м.
13. The hydraulic booster pump рулевего managements
Before installation fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel
14. An arm
15. A high pressure tube
16. A sealing ring
Always replace
17. A bolt "банджо", the inhaling moment: 45 Nanometers.
18. A soaking up hose
19. 20 Н.м.
20. A sealing ring

Tank of the hydraulic booster of a steering


1. A hose of the return pipeline
2. A collar
3. The tank is filled by a hydraulic liquid
Check up liquid level in a tank (on marks
On the tank) after the engine паработает during 2минут, wheels thus should stand directly
Muffle the engine, check up level of a liquid and add to a mark the MOVE if it is necessary
4. A collar
5. A soaking up hose
6. The filter
Clean a cleaning solution
7. A spring clamp
It is put on on probe for measurement of level of a liquid
8. A spring
9. Уплотнительно a ring
10. A cover of a jellied aperture

The pump of system of hydrostrengthening of a steering

1. A lining plate *
It is inserted into a lining
2. Прокладка*
3. A plate with apertures
4. A lock ring *
5. 15 Н.м.
Grease with hermetic D6 before installation
Longer end twists in the pump case
6. A shaft of the pump with a flange check up on presence of scratches and wear tracks
If it is necessary, replace all pump
Remove poтор and a shaft for
Replacements of a sealing ring
7. Sealing кольцо*
For replacement, it is necessary to disassemble the pump
8. The case
Oil channels (are specified by an arrow) both halves of the case should coincide after assemblage
9. Sealing кольцо*
10. A rotor
11. Blades
The polished surface (it is specified by an arrow) should be turned outside
12. Статор
Installation position: the arrow on статоре should be visible after installation
13. A valve clamp
аккумратно remove by means of small отверкти
14. The restrictive valve, do not assort
15. A spring
16. The case

The dual hydraulic pump for model with 20-klapannym the engine

1. A bolt for a tension клинового a belt
2. A clip
3. 20 Н.м.
4. A rotary arm
5. 20 Н.м.
6. З0Н.м.
At untwisting or removal, always replace with a detail 100 067 04
7. A mobile arm
8. 20 Н.м.
9. 20 Н.м.
10. A klinovoj belt, the size: 12.5x992 mm
11. A pulley, establish a mark "5Z" forward
12. 10 Н.м.
13. The pump with two pistons
Systems сервоусиления brakes
14. The lopastnoj pump
Before installation, fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel
15. The return pipeline, from a tee
16. The high pressure tube, goes to рейке a steering
17. 50 Н.м.
18. 20 Н.м.
19. 35 Н.м.
20. A high pressure tube