Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
- 5. Fuel system
   - 5.2. Systems of injection of fuel
      5.2.1.2. Specifications (4-cylinder models)
      5.2.1.3. Components of system of injection for 5-cylinder models
      5.2.1.4. Specifications (5-cylinder models)
      5.2.1.5. A starting position of a plate of the gauge of an air stream
      5.2.1.6. A free wheeling of a plate of the gauge of an air stream
      5.2.1.7. The lever of a plate of the gauge of an air stream
      5.2.1.8. Operating плунжер
      5.2.1.9. The throttle valve
      5.2.1.10. A rope of management throttle заслонкой
   5.2.2. Fuel injectors (20-klapannye models)
   + 5.2.3. An electronic control system of engine MPI
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment




5.2.1.3. Components of system of injection for 5-cylinder models
THE GENERAL DATA

Components of system of injection for 5-cylinder models

1. Return топливопровод (to the fuel tank)
2. 20 Н.м.
3. A regulator of pressure of fuel
4. An arm
5. 20 Н.м.
6. 10 Н.м.
7. A ventilating hose (to the top part of the air filter)
8. A bolt (antimagnetic)
9. A pressure difference regulator
About 17,5–21,5 Ohm
10. The electroplug
11. The lock screw of operating плунжера
12. The electroplug
13. Ventilation картера the engine
14. For idling stabilisation
15. A cover of soaked up air
16. The electromagnetic valve of the coal filter
17. To the coal filter
18. Ring consolidation
19. A sealing ring
Smaller diameter is directed to the managing director плунжеру
20. Operating плунжер
21. The fuel distributor
After installation of the fuel filter, check up a free wheeling of a plate of the gauge of an air stream
22. 20 Н.м.
At replacement establish a bolt "банджо* instead of the minifilter
23. 10 Н.м.
24. Шестигранная заглушка
25. To the valve of start from a cold condition
26. 10 Н.м.
27. Submitting топливопровод (from the fuel filter)
28. To инжекторному to the valve
29. 3.5 Н.м.
30. 20 Н.м.
31. 3.5 Н.м.

Components of system of injection for 5-cylinder models

1. Заглушка
Remove before adjustment of deduction WITH
2. An electrosocket
3. A potentiometer
4. Ring consolidation
5. A hose (to a final cranked branch pipe)
6. The channel приточного air
The channel приточного air has the managing director заслонку and the thermostat
The managing director заслонка closes, above +10 With: inflow of warm air
More low 0 With: inflow of cold air
7. A connecting hose
8. A casing of the air filter
нижняячасть
9. 20 Н.м.
10. A filtering element of the air filter
11. A casing of the air filter
The top part
12. A lining
13. A casing of the gauge of an air stream
14. The mesh filter
Installation position: curvature to a cover

Components of system of injection for 5-cylinder models

1. The electroplug
2. An arm
3. The mode switch completely open throttle заслонки
4. Fastening of a rope of management throttle заслонкой
5. To запорному клвпану the coal filter
6. The switch of a mode of idling
7. A clip
8. 20 Н.м.
9. A lining
10. An inlet collector
The top part
11. To the amplifier of brake system
12. The electroplug for the oxygen gauge
13. The oxygen gauge
50 Н.м.
Cover a carving with structure G5
In каталитическое the converter
14. The electroplug for the oxygen gauge
Heating element

15. 10 Н.м.
16. An arm
17. A thermoswitch
For postoperative work of the delivery fan, for cooling of fuel injectors
18. An arm of fastening of a rope of gas
19. A lining
20. The block of management of fuel injection
For сиситемы injection, management of the oxygen gauge and idling stabilisation
21. The electroplug of the block of management
Disconnect or connect the electroplug only at the switched off ignition
For removal unhook a spring clamp on the management block

Components of system of injection for 5-cylinder models

1. 10 Н.м.
2. To the fuel distributor
3. The valve of start from a cold condition
4. 10 Н.м.
5. A clamp
6. To the fuel distributor
7. 20 Н.м.
8. Топливны an injector
9. Ring consolidation
Cover with greasing before installation
10. Всавка for a fuel injector
11. The rubber block of fastening
12. Электрдразъем
13. 10 Н.м.
14. An arm
15. The operating valve for idling stabilisation
16. An insert for a fuel injector
17. Rings
18. The combined temperature gauge
19. A system flange
20. A sealing ring
21. The electroplug
22. A lining
23. 10 Н.м.
24. To a cover of soaked up air
25. An arm for fuel injectors
26. An inlet collector
The bottom part
27. A lining
28. An electrosocket