Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
- 10. Brake system
   10.1.2. Brake Pads forward brakes
   10.1.3. Brake Pads back brakes
   10.1.4. The general adjustment of back brakes (Girling)
   10.1.5. Replacement brake колодок (all-wheel drive models)
   10.1.6. The general adjustment of back brakes (Girling) (all-wheel drive models)
   10.1.7. Plugs of pedals of a brake and coupling
   10.1.8. Adjustment of a manual brake
   10.1.9. Removal of the lever of a manual brake
   + 10.2. Hydraulic components
   - 10.3. Antiblocking system of brakes
      10.3.2. The hydraulic pump
      10.3.3. The electronic block of management
      + 10.3.4. Elements ABS of a forward wheel
      - 10.3.5. Elements ABS of back brakes
         10.3.5.1. Gauges of speed of rotation of back wheels
      10.3.6. Broad-brush observations on repair
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment




10.3.5.1. Gauges of speed of rotation of back wheels Removal

PERFORMANCE ORDER
1) remove a fastening bolt (it is specified by an arrow) and get the gauge of speed
2) replace a sealing ring of the gauge of speed
3) grease a sealing ring and the gauge with greasing of the mechanism of brakes

4) establish the gauge in a rack nest so that полихлорвиниловый the tip concerned a rotor on the SHRUS


The prevention

After the gauge of speed has been removed and established some times, replace old полихлорвиниловый a cap and establish new, a detail 437 927 809. It is necessary for maintenance of a demanded air backlash.
5) establish a new fixing bolt and tighten it to 10 Н.м., keeping the gauge of speed, having pressed it to a rack of the bearing of a nave
6) insert the rubber plug of wires into an arm on a rack of the bearing of a nave

Both sockets of connection of gauges of speed of rotation of back wheels are established under back sitting.

Rotor, installation

The acceleration switch, removal / installation

The arrow and on the switch specifies on in front of the car

Arrangement: under back sitting on a left-hand side.

At removal / to installation, switch off ignition.

Do not establish the switch of longitudinal acceleration on the car on which it has not been established by manufacture. On the cars which are let out since April, 1988, this switch is established.

The switch of longitudinal acceleration is not required for effective work ABS.

The gauge of speed of rotation of wheels, installation (all-wheel drive models, release till January, 1989 of release)

PERFORMANCE ORDER
Insert rubber plugs of the gauge into an arm on the suspension bracket lever (are specified by arrows)

Both sockets of connection of gauges of speed of rotation of back wheels are under back sitting.

Rotor, installation

Removal / installation

PERFORMANCE ORDER
1) remove a fastening bolt (it is specified by an arrow) and get the gauge of speed
2) replace a sealing ring of the gauge of speed
3) grease a sealing ring and the gauge with greasing of the mechanism of brakes
4) establish the gauge in a rack nest so that полихлорвиниловый the tip concerned a rotor on the SHRUS
5) establish a new fixing bolt and tighten it to 10 Н.м., keeping the gauge of speed, having pressed it to a rack of the bearing of a nave
6) insert rubber plugs of wires into arms on a rack of the bearing of a nave

Both sockets of connection of gauges of speed of rotation of back wheels are under back sitting.