Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
- 12. A body, salon
   12.2. The central section of a guard
   12.3. A cowl rope
   12.4. A forward guard
   12.5. A forward wing
   12.6. Lock pins of a cowl, the rubber shock-absorber
   12.7. A cowl
   12.8. A gazonapolnennaja rack (models the Sedan)
   12.9. A luggage carrier cover
   12.10. A back door (Compartment model)
   12.11. A forward door, the bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing stoppers, a window regulator
   12.14. The door lock
   12.15. Draught of lever transfer of the lock
   12.16. A rope of an internal door-lock
   12.17. A rotary clamp, an adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. The central lock
   12.21. The pump with two modes of forcing
   12.22. The leading activator
   12.23. The activator of a back door
   12.24. The activator of a cover of a luggage carrier
   12.25. The activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt overlay (Compartment model)
   12.28. A skeleton of a back door, the bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. A rope, шарнирный the lever
   12.31. The door handle
   12.32. The holder of components of a door
   12.33. The hatch
   12.34. A bumper casing
   12.35. Hermetic sealing of a back bumper
   12.36. An extending clamp
   12.37. A forward spoiler / a lining of a niche of a wheel (Compartment model)
   12.38. The top overlay of a forward spoiler (Compartment model)
   12.39. A back spoiler / a lining of a niche of a wheel
   12.40. A back bumper (Compartment model)
   12.41. window raiser
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. A central air
+ 14. An electric equipment




12.13. Window condensing stoppers, a window regulator
THE GENERAL DATA

Window frame in assemblage


1. A bolt with шестигранной a head
крепит a bearing element to a door frame
2. A window sealant
3. A window regulator
Remove only when the bearing element of a door is removed
4. An overlay
5. A clamp for a rope of a regulator of a window
6. Door glass
Remove only when the bearing element of a door is removed
7. A lock washer
8. A washer
9. A prokladochnoe ring
10. The shock-absorber
11. A bolt with шестигранной a head 6 Н.м.
12. Заглушка
13. A cover of the internal lock of a door
14. A bearing element of making elements of a door
15. A door frame

Window regulator in assemblage


1. A condensing lining of door glass
2. A lock washer
3. A washer
4. The amortisation plug
5. Door glass
Remove bearing element of a door
6. A window regulator
Remove together with a bearing element of a door
7. A cover of the lock of a door
8. A fixing pin
9. A bolt with шестигранной a head for doorframe fastening
10. A shestigrannaja nut 6 Н.м.
11. A plate of the holder
12. A door frame
13. A condensing lining

Condensing stoppers

Insert from below in directing windows

And = 65 mm

It is measured from the end of a groove of a window


The stopper is used as a sealant, and also antinoise means.

Window regulator

Removal

PERFORMANCE ORDER
1) remove bearing element of components of a door
2) remove a lock washer 2
3) remove an assembly washer and a protective material
4) pull out a window from a shutter of the elevating mechanism of a window
5) unbend a clip 7 in a direction of an arrow and pull out a rope from a clip
6) unscrew bolts with шестигранной a head 6
7) unscrew bolts with шестигранной a head 16

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER
1) screw up bolts with шестигранной a head 6 Н.м.
2) place shock-absorbers between a window and a bearing element
3) check up a window and if necessary adjust it

Window frame in assemblage (Compartment model)

1. The screw, 20 Н.м.
2. An aluminium clamping overlay
3. A clip, external
4. A clip, internal
5. Door glass
6. An adjusting clamp
7. A window regulator
8. A butt overlay
9. The screw, 20 Н.м.
10. The buffer
11. An arm
12. A nut, 6 Н.м.
13. A bolt, 15 Н.м.
14. An adjusting washer
Establish, as it is required
15. A bolt, 15 Н.м.
16. A flat nut / a washer, 15 Н.м.

Window regulator, removal / installation (Compartment model)
The prevention

The site of intermediate rings should be noted before removal of a regulator of a window.


Removal

PERFORMANCE ORDER
1) remove the decorative panel of a door
2) note a site of four top bolts of a regulator of a window (an arrow
3) ослабьте the bottom bolts of a regulator of a window (an arrow
4) remove intermediate rings
5) unscrew all six bolts of a regulator of a window
6) remove a regulator of a window from a door

Installation

PERFORMANCE ORDER

1) paste sticky strips, as is shown in drawing, on a window

Pencil note the size and = 20 mm

2) establish a window regulator in a door covering
3) insert draught of the lock with the door-lock button
4) establish into place all bolts of a regulator of a window and tighten manually
5) pay attention to the marks made round the top bolts
6) close a door and check up the sizes:

b = 19.5 – 21.00 mm

With = 12.0 – 15.0 mm

The prevention

If the sizes do not correspond specified, move a window regulator in a door covering while the sizes will not coincide with the specified.

Rough pressure of glass in the field of the central rack of a body or discrepancy of the sizes b and with the demanded can cause noise from a wind or a leak.


7) place intermediate rings under bolts
8) close a door and check up pressure of glass upon a door; the door should be closed easily

Window regulator, check (Compartment model)
PERFORMANCE ORDER
1) open a door
2) with a chalk rub edge of glass which touches the central rack of a body
3) close and again open a door
4) check up a print left a chalk on the condensing lining of a window
5) if a print is on all length of a condensing lining, door glass is established correctly; if is not present: add or clean intermediate rings, and then anew carry out check
6) close a door and a window

7) place a metal ruler outside how it is shown in drawing

And = 17 – 18 mm

To reach the size and, the butt overlay can be adjusted

8) establish the decorative panel of a door
9) check up the car on noise from a wind and a leak

Window regulator, adjustment (Compartment model)


The prevention

The covering of a window and door is necessary for regulating first of all.


PERFORMANCE ORDER
1) ослабьте bolts (arrows)
2) close a door
3) two experts further be required; slightly press on bearing element in a direction opposite to a roof and a rack
4) will apply slightly more forces, than it is necessary. The rubber lining will return bearing element in appropriate position
5) at this time the second expert (from within the car) places intermediate распорки between a covering of a door and a window regulator
6) establish bolts from under a bottom and tighten; 15 Н.м.

Window regulator (models of the Compartment 1990 modelling years)

Removal

PERFORMANCE ORDER
1) remove bearing element of a door
2) remove a lock washer 2
3) remove a fixing washer and the loose leaf
4) remove a window, unscrew adjusting bolts
5) unscrew bolts with шестигранной a regulator head in the bottom part of a door

Installation

Installation carry out upside-down, in view of the following:
PERFORMANCE ORDER
1) tighten bolts with шестигранной a head with the moment 6 Н.м.
2) place the loose leaf between a regulator of a door and glass
3) check up and if necessary adjust a window arrangement
The prevention

Turn an adjusting detail for free wheeling adjustment between the handle of a door and the door lock.

During adjustment it is not necessary to apply force to the squeezing lever.


4) the maximum free wheeling between the squeezing lever and the adjusting adaptation 0.5 – 1.0 mm

Arrangement of elements

The condensing flange should adjoin to glass in course avoidance.

Condensing stopper

To place in a window groove

And = 25 mm

It is measured from the end of a groove of a window