Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. A steering
11.2. A shaft and a casing of a steering column
11.3. A power absorbing steering column
11.4. A steering drive
11.5. The pipeline of high pressure / the return pipeline
11.6. Free wheeling adjustment рейки a steering
11.7. A klinovoj belt
+ 11.8. System of hydrostrengthening of a steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment
|
Steering drive
1. Steering transfer
Establish precisely on the centre of a shaft of a steering column
Establish steering transfer so that there were no warps and a tension
If it is necessary, move it
It is a little in fastening places
2. An arm of cross-section draught
At an inhaling of nuts of fastening of cross-section bent for to an arm, the car should stand on the earth
3. 45 Н.м., always replace
4. 45 Н.м., always replace
5. A washer
6. High pressure pipelines. The moment of an inhaling of fastening: 50 Н.м.
Establish шланговый a clip on
Inlet hose before removal
7. 20 Н.м., always replace
8. A washer
9. A wheel casing |
10. A bolt with a head under a face key
Tighten before an inhaling of bolts of fastening of steering transfer to the body panel
11. A spring washer
12. A cover
Do not remove from the body panel at removal of steering transfer
Establish accurately in a round flute on a casing of the main gear wheel
13. A bolt, always replace
14. A connecting disk remove from a leading gear wheel together with a tube with flanges
15. 25 Н.м., always replace
16. The body panel
17. The return pipeline
18. Sealing rings, always replace
19. A bolt "банджо"
The inhaling moment: 40 Н.м.
Before untwisting, establish шланговый a clip on the return pipeline |
Steering drive (models of release till January, 1989 of release)
1. A cover
It is possible to replace, without removing реечный the steering mechanism
2. A lock ring
Put on on рейку a steering against the stop
Establish a cover on a flute,
Passing on a ring circle
3. 20 Н.м.
4. A cover
5. A sealing ring *
Always replace
6. The epiploon plug
It is established by thicker end upwards
7. A toddler
The flute is turned to a cover
8. The case рейки a steering
If the case surface is damaged in an installation site of a gear washer, accurately eliminate damage before epiploon installation рейки
9. Рейка a steering
Check up рейку on presence of scratches round an epiploon installation site
10. A cap
The inhaling moment: 50 Н.м.
Tighten by means of two кернеров, established at an angle in 180 to each other |
11. Basic кольцо*
Always replace
It is established on a cap
12. A sealing ring *, 44x2.5 mm
Always replace
It is established on a cap
13. A sealing ring *, 42x2 mm
14. A sealing ring *, always replace
15. A washer
16. The needle bearing
17. A washer
18. Conducting шестерня*
19. An epiploon
20. 20 Н.м.
21. A casing of a leading gear wheel
22. The ball-bearing
23. A sealing ring
Always replace
24. A spring
It is inserted into a toddler
25. A ring
26. An epiploon рейки the helmsman управления*
27. A lock ring
Check up correctness of installation
28. A gear washer
Check up correctness of installation
29. A collar
Use a collar which is pulled together by means of the screw, the screw should be turned to a body |
The system of hydrostrengthening of a steering is filled by a hydraulic liquid, detail G 002 000. All elements marked with an asterisk, are included in the repair complete set and should be replaced during repair.
The prevention
Moisten all epiploons in a hydraulic liquid before installation. Do not try to straighten elements of a steering or to spend on them repair welding works.
Works with a steering drive should be spent on a pure workplace and all elements should contain in absolute cleanliness.
|
|